Create Account

Hofmann 14K Scissor Alignment Lift - EELR789APKG

Hofmann 14K Scissor Alignment Lift - EELR789APKG
application carCar
application light truckLight Truck

Hofmann 14K Scissor Alignment Lift - EELR789APKG

  • SKU: HOF-EELR789APKG $30,009.00
  • Save $1,942.32


Free Shipping
Ground Shipping to Lower 48 States
Alaska, Hawaii, & any/all US territories & international orders are excluded.


Hofmann Scissor Alignment Lifts are easy to operate, provide increased accessibility to alignment adjustment areas, and are easy to load. Space-saving design allows for up to five scissor lifts to fit into the same operating space as four 4-post lifts.

Locked and Lighted models provide productivity enhancements while allowing the technician to perform critical tasks while minimizing alignment process operations by illuminating both inspection and adjustment areas and sequencing the locking of alignment plates.


  • Maintenance reduced rear slip plates use oversized, encapsulated bearings that roll upward to protect against environmental debris
  • Four hydraulic cylinders in a cross aligned arrangement provide secure lifting power and added safety
  • Approach ramps are equipped with end sliders to minimize noise and reduce floor damage
  • Adjustable maximum lift height suits locations with low ceilings
  • On-board Filter/Regulator/Lubricator / FRL provides clean and lubricated air to help reduce maintenance and protect pneumatic systems
  • Mechanical locking with pneumatic safety lock release from the control console
  • Flow sensing valves within the hydraulic control circuit
  • Redundant hydraulic safety system with cross aligned hydraulic circuits
  • Illuminate alignment adjustment and calibration areas
  • Front LEDs are mounted in the front turnplate base to accommodate varying vehicle wheel tracks easily
  • Rear LEDs are strategically positioned on the rear slip plates
  • Ease locking control activation from the lift console to reduce walking and effort from resetting alignment pins in plates
  • Locking components made from corrosion-resistant material
  • Patented auto on/off light feature ensures no power when operating in the hazard zone
  • Patented light mounting position optimizes viewing angle, illuminating key inspection and adjustment areas
  • Approved for use in Class 1 Division 1 environments for both surface and flush mount models
  • Tested and validated by an independent third party to the ANSI/ALI automotive lift standard, ALCTV-2011


Maximum Capacity: 14000 lbs / 6350 kg
Overall Width: 92.5in / 234.95 cm
Width Between Runways: 38in / 96.52 cm
Overall Length: 270in / 685.8 cm
4 Wheel Alignment Wheelbase: 88in - 155in / 223.52 cm - 393.70 cm
2 Wheel Alignment Wheelbase: 180in / 457 cm
General Service Wheelbase: 194in / 492.8 cm
Runway Surface Length: 210in / 533.4 cm
Runway Surface Width: 26in / 66 cm
Maximum Raised Height: 72in / 182.9 cm
Minimum Lowered Height: 10in / 25.4 cm
Lifting Time at Full Load: 75 to 85 seconds
Motor: 3 hp
Air Supply Requirements: 90 - 120 PSI
Power Supply Requirements: 230 VAC, 50/60 Hz, 1 Ph, 20 Amp
Shipping Weight without Jacks: 6387 lbs / 2897 kg
Console Dimensions / DxWxH: 16.5in x 14.125in x 45.75in

RJ217 Rolling Jack
Capacity: 7000 lbs / 3175 kg
Minimum Arm Reach: 31in / 787 mm
Maximum Arm Reach: 53in / 1346 mm
Minimum Lowered Height: 1in / 25 mm above the deck surface
Maximum Raised Height: 12.75in / 324 mm above the deck surface
Air Supply Requirements: 90 - 120 PSI / 6 - 8 bar
Maximum Operating Pressure: 5210 PSI / 359 bar
Shipping Weight: 329 lbs / 149 kg


2 x RJ217 Rolling Jacks (7,000 lb capacity each)
2 x EAK0336V49A Premium Front Radius Turnplates with Lights & Locks Feature
1 x EAK0277J28A Rollback Paddle Kit
LED Lights in Front Turnplate Base and Rear Slip Plates
Locking Control Activation Feature from Lift Console for Alignment Plates

Other Popular Items:

Recently Viewed Items